Hyundai Ioniq: Smart Key System / Smart Key Diagnostic. Repair procedures
Self Diagnosis with Scan Tool
It will be able to diagnose defects of SMART KEY system with GDS quickly. GDS can operates actuator forcefully, input/output value monitoring and self diagnosis.
The following three features will be major problem in SMART KEY system.
1. | Problem in SMART KEY unit input. |
2. | Problem in SMART KEY unit. |
3. | Problem in SMART KEY unit output. |
So the following three diagnosis operates will be the major problem solution process.
4. | SMART KEY unit Input problem : switch diagnosis |
5. | SMART KEY unit problem : communication diagnosis |
6. | SMART KEY unit Output problem : antenna and switch output diagnosis |
Switch Diagnosis
1. | Connect the cable of GDS to the data link connector in driver side crash pad lower panel, turn the power on GDS. |
2. | Select the vehicle model and then SMART KEY system. |
3. | Select the "SMART KEY Unit". |
4. | After IG ON, select the "Current Data". 
|
5. | You can see the situation of each switch on scanner after connecting the "current data" process.
Display
| Description
| FL Toggle SW
| ON : Push button is ON in the driver door handle.
| FR Toggle SW
| ON : Push button is ON in the assist door handle.
| Tailgate open SW
| ON : Tailgate button is ON.
| Gear P Position
| ON : Shift lever is P position.
| IGN 1
| ON : IGN switch is IG position.
| ACC
| ON : IGN switch is ACC position.
| Brake SW
| ON : Brake switch is ON.
|
|
Communication Diagnosis with GDS (Self Diagnosis)
1. | Communication diagnosis checks that the each linked components operates normal. |
2. | Connect the cable of GDS to the data link connector in driver side crash pad lower panel. |
3. | After IG ON, select the "DTC". 
|
Antenna Actuation Diagnosis
1. | Connect the cable of GDS to the data link connector in driver side crash pad lower panel. |
2. | After IG ON, select the "Actation Test". 
|
3. | Set the smart key near the related antenna and operate it with a GDS. |
4. | If the LED of smart key is blinking, the smart key is normal. |
5. | If the LED of smart key is not blinking, check the voltage of smart key battery. |
Antenna Status Check
1. | Connect the cable of GDS to the data link connector in driver side crash pad lower panel. |
2. | Select the "Antenna Status Check". 
|
3. | After IG ON, select the "Antenna Status Check". 
|
4. | Set the smart key near the related antenna and operate it with a GDS. 

|
5. | If the smart key runs normal , the related antenna, smart key(transmission, reception) and exterior receiver are normal. |
FOB Status Check
1. | Connect the cable of GDS to the data link connector in driver side crash pad lower panel. |
2. | After IG ON, select the "FOB Key Status Info". 

|
Smart Key Status Check
1. | Connect the cable of GDS to the data link connector in driver side crash pad lower panel. |
2. | After IG ON, select the "SMK Status Info". 

|
Neutralization Status Check
1. | Connect the cable of GDS to the data link connector in driver side crash pad lower panel. |
2. | After IG ON, select the "Neutralization Mode". 



|
RemovalSmart Key Unit1.Disconnect the negative (-) battery terminal.2.Remove the glove box.(Refer to Body - "Glove Box Upper Cover Assembly")3.Remove the smart key unit (A) after disconnecting the connectors (B) and loosening the bolt and nut...
Other information:
Basic Service SymbolsThere are five primary symbols used to complement illustrations. These symbols indicate the part to apply such materials during service.
Symbol
Meaning
Do not reuse the part. Replace a new one...
Removal1.Disconnect the negative (-) battery terminal.2.Remove the roof trim assembly.(Refer to Body - "Roof Trim Assembly")3.Disconnect the roof antenna cable and connectors (A).4.Remove the roof antenna after loosening a nut (A).Installation
•
Make sure that the cables and connectors are plugged in properly...
Categories
Seat belt warning light

As a reminder to the driver, the seat belt warning light will illuminate and
warning chime will sound for approximately 6 seconds each time you place the Engine
Start/Stop button to the ON position if the seat belt is unfastened.
read more